| EPSRC Reference: |
EP/T018739/1 |
| Title: |
Experimental Flight Dynamics Testing for Highly Flexible Aircraft |
| Principal Investigator: |
Lowenberg, Professor M |
| Other Investigators: |
|
| Researcher Co-Investigators: |
|
| Project Partners: |
|
| Department: |
Aerospace Engineering |
| Organisation: |
University of Bristol |
| Scheme: |
Standard Research |
| Starts: |
01 September 2020 |
Ends: |
12 October 2023 |
Value (£): |
651,494
|
| EPSRC Research Topic Classifications: |
| Aerodynamics |
Materials testing & eng. |
|
| EPSRC Industrial Sector Classifications: |
| Aerospace, Defence and Marine |
Transport Systems and Vehicles |
|
| Related Grants: |
|
| Panel History: |
|
|
Summary on Grant Application Form |
The aerospace sector, in its ongoing quest to improve aircraft efficiencies, is considering more flexible and finely tuned aero-structural systems. One such approach is to increase the aspect ratio (AR) of the wings, i.e. increase the span such that the wings are more slender. Such higher aspect ratio wings offer the prospect of improved aerodynamic efficiency for civil and military transport aircraft and for certain types of unmanned aircraft, such as those used for high-altitude long-endurance sensing, environmental monitoring, etc.
High AR wings are typically more flexible than conventional designs in order to minimise structural mass. This in turn can increase the complexity of the dynamic responses of the wings themselves and the aircraft as a whole. These responses comprise different modes of motion, associated with airframe aeroelasticity (which refers to the interaction between airframe aerodynamic, structural and inertial properties) and with the so-called 'rigid-body' motions (representing the behaviour of the air vehicle independent of any elastic/flexibility effects) and flight control modes.
In design and analysis of conventional (more rigid) aircraft, the aeroelastic modes are typically at higher frequencies than the flight dynamics and control modes and are usually able to be well modeled using linear methods; in such air vehicles the extent and complexity of any coupling with the flight dynamics behaviour is low. However, the more flexible the airframe, the stronger the likely interaction (coupling) between all these modes. Furthermore, the influence of nonlinearity increases - in particular geometric nonlinearity in high AR wings, along with other potential nonlinear characteristics such as in the aerodynamics and control system.
Methods for numerical modeling of highly flexible aircraft, incorporating the necessary coupling and nonlinear phenomena, have been extensively researched and developed in recent years. Validating or calibrating these predictive methods via controlled experiments is, however, a challenge - usually addressed by testing a wing as a cantilever supported rigidly at its root in a wind tunnel. There is very limited scope in existing test rigs for extending the experimental approaches to accommodate the degrees of freedom needed to capture the coupling between the flight dynamics and control modes and the aeroelastic modes. Such rigs that do exist are usually intended for limited motion amplitudes in order to test for onset of aeroelastic instability, rather than being aimed at large-amplitude wing bending, torsion and model motions to exploit or explore nonlinearity.
This proposal introduces a new experimental concept that allows this coupled behaviour to be investigated in a controlled wind tunnel environment. It entails a challenging extension to the current testing approach for the University of Bristol's novel 5-degree-of-freedom dynamic test rig and the design of suitable flexible actuated and instrumented models. The procedure will build on previous rigid-body test accomplishments and will extend earlier work on active rig control to ensure that coupled dynamic phenomena seen in the wind tunnel match those of free flight as closely as possible.
A successful outcome of this exploratory research could launch the development of this new test technique towards implementation in industrial wind tunnels. It will also assess the feasibility of extending the capability to incorporate load alleviation control in the flexible wings. Furthermore, it will generate enhanced types of data to evaluate the predictive ability of nonlinear computational modelling techniques and to adapt or calibrate them to measured behaviours. In this way, the proposed research offers the prospect of substantially improved wind tunnel capability to support design and analysis of future advanced aircraft wings/airframes featuring complex dynamic interactions.
|
|
Key Findings |
|
This information can now be found on Gateway to Research (GtR) http://gtr.rcuk.ac.uk
|
|
Potential use in non-academic contexts |
|
This information can now be found on Gateway to Research (GtR) http://gtr.rcuk.ac.uk
|
|
Impacts |
|
| Description |
This information can now be found on Gateway to Research (GtR) http://gtr.rcuk.ac.uk |
| Summary |
|
| Date Materialised |
|
|
|
|
Sectors submitted by the Researcher |
|
This information can now be found on Gateway to Research (GtR) http://gtr.rcuk.ac.uk
|
| Project URL: |
|
| Further Information: |
|
| Organisation Website: |
http://www.bris.ac.uk |